WEEK 17

On 20 November 2019, I had email my proposal report to Madam Azliza for plagiarism check. After that, around 11.13 am, Madam Azliza  had tell me that she already check for my plagiarism which is 23% for FYP 1 and Madam ask to print out the proposal report and submit to her by this week.

After that, on 21 November 2019, i had print out my full report and the price for printing is RM 17.00. So, I keep the receipt to claim for FYP project budget and submit the proposal report to Madam Azliza.

On 23 November 2019, I submitted my progress report by using blogger. On this blogger, I had explain all of my progress on my FYP 1 project by week and i will continue my progress for FYP 2 by using same blogger.

https://syedamsyarfyplogbook.blogspot.com/

WEEK 16

This week is the last week before all student FYP 1 should submit their FYP proposal report and progress report. I had done around 90% for my proposal report, so i had continue chapter 3, that is gantt chart. Gantt chart is chart that i need to show my progress for this project in the chart. This can make easier for reader to know my progress of the project. I had also done for my conclusion, which is i am done my FYP proposal report. Therefore, I had start to recheck and touch up my report.

Gantt Chart for Hand Motion Robotic Arm

On 16 October 2019 (13.42pm), Madam Azliza had whats app me on FYP group that she remind me to submit my proposal report for checking the plagiarism. This is because, the submission for proposal report is on next week. 

However, I had a problem on my chapter 2, that i need to repair the literature review. So, I need to delay my proposal report from submitted to madam. 

WEEK 15

This week, i had continue Chapter 3, which is schematic diagram, project equipment and software. For schematic diagram, I need to find expected schematic diagram for my project. This is main part of the robotic arm diagram that need to simulate to get the output. However, on the diagram below (picture) show the four motor but for my project used 2 servo motor only. 

Schematic Diagram

After that, Project equipment and Software is what i need to build my robotic arm project. This is can make easier for me to survey the project price and estimated my FYP project's budget. I have used 10 material and equipment to develop this project.

Material and Equipment:

1. Robotic arm chassis
2. Arduino Uno R3
3. Hand glove 
4. 8051 series microcontroller
5. servo motor
6. AT Mega controller
7. Accelerometer
8. RF module
9. Encoder & Decoder
10. Driver IC

This is example that i am doing on my proposal report

After I had list my material and equipment, so i can start survey my material price on internet. Mostly the small and familiar component can buy by online. I had survey on shopee, Lazada and other website. I am also will survey at Jalan Pasar, Pudu Kuala Lumpur.

Link: https://shopee.com.my/search?keyword=arduino%20uno

Link:  https://my.rs-online.com/web/p/products/7154081?cm_mmc=MY-PPC-DS3A-_-google-_-3_MY_EN_Processor+%26+Microcontroller+Development+Kits_Arduino_BMM-_-Arduino+-+Processor+%26+Microcontroller+Development+Kits+-+7154081-_-%2Barduino+%2Ba000066&matchtype=b&kwd-306201961359&gclid=Cj0KCQiAiNnuBRD3ARIsAM8KmltSfpP2GoqPY0GoqN_ZY-PRpJZ-CInjUDf61g20Dy03s9HQBU9QqyYaAl1_EALw_wcB&gclsrc=aw.ds